3D-Printed Device Could Help Cut Energy Bills and Carbon
June 14, 2019 | Swansea UniversityEstimated reading time: 2 minutes
A new 3D-printed thermoelectric device, which converts heat into electric power with an efficiency factor over 50% higher than the previous best for printed materials--and is cheap to produce in bulk--has been manufactured by researchers at Swansea University’s SPECIFIC Innovation and Knowledge Centre.
Image Caption: Thermal camera image: achieving record-breaking efficiency using new printed thermoelectric material
Around one-sixth of all the energy used by industry in the UK currently ends up as waste heat, emitted into the atmosphere. Harnessing this to create electricity could be a huge step forward in helping the industry cut its energy bills and reduce its carbon footprint.
Thermoelectric materials turn differences in temperature into electric power or vice versa. They are used in fridges, power plants and even some smartwatches that are powered by body heat.
Previous research has shown that a material called tin selenide (SnSe), a compound made up of tin (Sn) and selenium (Se), has high potential as a thermoelectric material. The problem is that the methods used to manufacture it require lots of energy and are therefore expensive.
This is where the Swansea researchers’ work comes in. The technique they have developed is potentially very low-cost for industry because it enables SnSe thermoelectric generators to be produced quickly and easily in large quantities.
The team formulated tin selenide into a type of ink which they could print to test its properties. The next step was to develop a type of 3D-printing technique to produce a small thermoelectric generator made out of the ink.
The team’s experiments showed that the material gave record scores for efficiency in performance, which is measured by the “Figure of Merit” (ZT).
The Swansea team’s element achieved a ZT value (a measure of the thermoelectric generator's efficiency) of up to 1.7
The previous best ZT score for a printed thermoelectric material was 1.0
This means an efficiency rate – for turning heat into electricity - for the Swansea team’s element of around 9.5%, compared with 4.5% for the previous best
The breakthrough could be of particular benefit to industries where high temperatures are involved in the manufacturing process.
One example is steelmaking, which generates vast amounts of heat and requires immense electrical power. Recycling the heat into power, therefore, has the potential to boost energy efficiency significantly. Tata Steel is due to support a Ph.D. researcher on the team to explore the industrial application of the technology.
Printing tin selenide to turn waste heat into electrical power
The research team is from SPECIFIC Innovation and Knowledge Centre, a Swansea University-led project which develops technologies for reducing carbon emissions and demonstrates how they can be applied to buildings and industry.
Dr. Matt Carnie of Swansea University, who was lead researcher for this work, said:
“Turning waste heat into electrical power can boost energy efficiency significantly, cutting bills and reducing carbon emissions. Our findings show that printed thermoelectric materials using tin selenide are a very promising way forward.
The device we developed is the best-performing printed thermoelectric material recorded to date, with the efficiency factor improved by over 50% compared to the previous record. It is also cheap to produce in bulk compared with established manufacturing methods.
More work is needed, but already our work shows that this technique, combining efficiency and economy, could be very attractive to energy-intensive industries.”
Suggested Items
Happy’s Tech Talk #26: Balancing the Density Equation
03/14/2024 | Happy Holden -- Column: Happy’s Tech TalkPrinted circuit design and layout is a creative process that has profound implications for electronic products. With the need for more parts on an assembly, or the trend to make things smaller to be portable or for faster speeds, the design process is a challenging one. The process is one of “balancing the density equation” (Figure 1) with considerations for certain boundary conditions like electrical and thermal performance. Unfortunately, many designers do not realize that there is a mathematical process to the layout of a printed circuit
A Brief History of IPC APEX EXPO
03/13/2024 | Alicia Balonek, IPCIn 1998, the Surface Mount Equipment Manufacturers Association (SMEMA) approached IPC for help. Because of IPC’s success with the Printed Circuits Expo and recognizing the need to establish control of its own event, the discussions between SMEMA and IPC ensued. This led to a merger between the two organizations and provided SMEMA with IPC member benefits.
Electronics Circuit World Convention: A Brief History
03/07/2024 | David Bergman, IPCIn 1978, a new event called the Printed Circuit World Convention (PCWC) was born. It brought together printed wiring board (PWB) associations from around the world to focus on advancing technology, growing the market, and providing insight into the management of the manufacture of printed boards.
Printed Electronics Industry Remains Positive But Cautious in 2024
03/07/2024 | OE-AThe results of the latest OE-A Business Climate Survey show slightly lower expectations for 2024 compared to the projections made in the 2023 surveys. However, the decline is at a high level: For 2024, responding association members expect a 13 percent increase in revenue for the flexible and printed electronics industry. "
IEC Confirms Install of Echo Graphic 751 Processor
03/05/2024 | IECLongest-serving distributor to the North American PCB industry, IEC (International Electronic Components) confirms that the Echo Graphic 751 Processor has been ordered and installed at a SMT printing solutions company in Toronto.