-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
IPC Plating Sub-committee 4-14: Surface Finish Specifications
May 27, 2015 | George Milad, UyemuraEstimated reading time: 1 minute
IPC specifications are reference documents to be called out by designers and OEMs. Designers may take exception with one or more items in the specification to ensure that the product meets the requirements of its intended use. The acronym AAUBUS (as agreed upon between user and supplier) is part of any specification.
Specifications are consensus documents. They are agreed upon by a panel of interested industry participants composed of suppliers, manufacturers, assembly houses (CMs) and end-users. The IPC Plating Sub-committee 4-14 is no exception.
When there is consensus, the committee documents it in a specification. In cases where no consensus is readily arrived at, the committee undergoes its own testing in what is commonly referred to as a round-robin (RR) study. In an RR investigation, an agreed-upon test vehicle (TV) is designed and manufactured. TVs are then sent around to the different suppliers who deposit the agreed upon thicknesses to be investigated. The TVs are collected and the deposit thicknesses are verified and documented. The TVs are then coded. The TVs are sent around again to the different testing sites that test for the desired attribute like soldering, contacting and wire bonding capabilities of different finish thicknesses. The data is then collected, sorted out and documented. At this point, a new attempt at consensus is made and upon arrival, the thickness specification is set.
A draft is prepared after consensus is complete. The draft is then posted for peer review. Any IPC member can review the document and suggest technical or editorial changes. All comments are then reviewed and all issues resolved before the final draft is issued. At this time the IPC takes on the task of publishing the document in its final format.
The IPC Plating Sub-committee 4-14 has been active since 2001. It is co-chaired by me and Gerard O’Brien of ST and S Group. The IPC liaison is Tom Newton. The sub-committee has an extensive member list composed of OEMs, contract assemblers, board manufacturers, and chemical suppliers, as well as labs and consultants.
To read this entire article, which appeared in the April issue of The PCB Design Magazine, click here.
Suggested Items
Real Time with… IPC APEX EXPO 2024: Understanding Objective Evidence in Manufacturing Processes
05/07/2024 | Real Time with...IPC APEX EXPOGraham Naisbitt explains the importance of objective evidence in manufacturing processes, debunking the common misconception that the ROSE test is a cleanliness test. He also discusses the introduction of Rev J, a requirement for measuring ionic contamination on circuit assemblies, and the challenges in accurately measuring contamination. Alternative methods like ion chromatography and the need for updating standards like the ROSE test are mentioned.
Real Time with… IPC APEX EXPO 2024: My Role as a Technology Solutions Director
05/02/2024 | Real Time with...IPC APEX EXPOPeter Tranitz, senior director of technology solutions at IPC, shares insights into his role as the design initiative lead. He details his advocacy work, industry support, and the responsibilities of the design initiative committee. The conversation also covers the revamping of standards, the IPC Design Competition, and the implementation of design rules in software tools.
HQ NextPCB of HQ Electronics Debut on the International Stage for Electronics Manufacture at IPC APEX 2024
05/01/2024 | PRNewswireHQ NextPCB of HQ Electronics, a leading Chinese-based multilayer PCB manufacturer and assembly house showcased its industrial prowess on the international stage for the first time at the IPC APEX Expo 2024.
IPC's Vision for Empowering PCB Design Engineers
04/30/2024 | Robert Erickson, IPCAs architects of innovation, printed circuit board designers are tasked with translating increasingly complex concepts into tangible designs that power our modern world. IPC provides the necessary community, standards framework, and education to prepare these pioneers as they explore the boundaries of what’s possible, equipping engineers with the knowledge, skills, and resources required to thrive in an increasingly dynamic field.
North American EMS Industry Down 4% in March
04/29/2024 | IPCIPC announced the March 2024 findings from its North American Electronics Manufacturing Services (EMS) Statistical Program. The book-to-bill ratio stands at 1.31.