-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
EM Modeling: The Impact of Copper Ground Pour on Loss and Impedance
May 2, 2019 | Chang Fei Yee, Keysight TechnologiesEstimated reading time: 1 minute
This article briefly introduces the general purposes of copper ground pour on printed circuit boards. Subsequently, the impact of copper ground pour on PCB channel loss in terms of insertion loss and impedance in terms of time domain reflectometry (TDR) is studied with electromagnetic modeling using Mentor HyperLynx.
Introduction
Copper ground pours are created by filling open, unpopulated, or unrouted areas on outer layers of the PCB with copper. Subsequently, copper fill is hooked up to ground planes on inner layers with stitching vias as depicted in Figure 1. Copper ground pours on outer layers provide extra shielding against electromagnetic radiation by signals on inner layers. Besides that, copper pour also serves as a heat sink for the voltage regulator module on PCBs. In terms of manufacturability, copper pour reduces the possibility of PCB warpage during reflow by balancing the amount of copper on each side of the PCB.
However, copper ground pour comes with some disadvantages, as there is a change in impedance of PCB trace adjacent to ground pour (i.e., impedance decreases when copper pour becomes closer to the PCB trace). As a result, the impedance mismatch contributes additional PCB loss to the transmission line at a high-frequency range.
Analysis and Results
To study the impact of copper pour on PCB channel loss in terms of insertion loss and impedance in terms of TDR, five models of 1” single-ended microstrip listed in Table 1 were created. The simulation topology is shown in Figure 2. For model 1A, a microstrip trace 5 mils wide and 1 oz. thick is laid out 2.65 mils above the reference plane insulated by low-loss dielectric substrate material. This trace is sandwiched between two ground traces on the same outer layer. The spacing between each adjacent ground trace and the signal trace is 1x the signal trace width. Meanwhile, the spacing between each ground and signal trace is set as 2x, 4x, 6x, and 8x for model 1B, 1C, 1D and 1E, respectively.
To read this entire article, which appeared in the April 2019 issue of Design007 Magazine, click here.
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: