Three Industry Giants From WKK Gather Around for Discussion


Reading time ( words)

During the recent HKPCA show I had the opportunity to catch up with Hamed El-Abd, Lionel Fullwood, and Gene Weiner. Our discussion covered an array of topics, from politics to new PCB factories and what it takes to stay competitive. Below is the transcription from our conversation.

007: Here with me today is Hamed El-Abd, Lionel Fullwood and Gene Weiner from WKK, welcome guys.

GW: Barry, it’s good to see you again in China, the number one economy in the world as of this quarter.

007: Thank you, and that’s what I’ve read just this morning.

GW: And that is clearly because of numbers, not because of technology. The leading technology here is still coming in from the foreigners, including the Taiwanese, who are classed as foreigner.

007: Gene you’ve been coming to China for many years now, correct?

GW: Since 1983.

007: One of the things that strikes me is the amount of change that has happened in just the last five years in particular. What changes have you seen and what’s your opinion on it?

GW: Well with the change a lot of it is superficial. Much of it is a new younger government tightening up, and much of it is from a stronger economic position globally and a stronger military. The Chinese have put themselves in a position to be a power player, if not the power player in the world. They’re still copying, copying, copying and not paying much attention to specs. Mostly it’s homegrown products for homegrown companies, with the best technology still coming from Europe, the U.S., Japan and Taiwan. From Taiwan I would say it’s the application of the technology improvements done by ITRI, their government sponsored research, as well as their major companies.

007: In comparison to the U.S., where obviously you've spent a lot of time, what do you see happening from your point of view?

GW: The U.S. is struggling to maintain a position with a government that appears confused with economic, domestic, and foreign policies. However, quietly happening in the U.S., and not for volume but for technology, we're seeing some great advances in R&D in chips, packages, chipsets, as well as the quiet building of new automated factories in captive shops not publicly known. Lockheed has three in-house printed circuit shops and the public thinks there's only one. It’s now become an open secret that Intel is building a shop in Chandler. Two weeks ago Lionel and I visited Whelen’s new factory in New Hampshire and it’s the first fully automated new printed circuit shop in North America—and I really mean fully automated. The only things that were not part of the automation line was a separate semi-automatic layup set-up and multilayer pressing line by Burkle, an offline ENIG electroless nicke/gold and a plasma machine. Everything else was inline, automated, with a very modern design. Instead of treating the air and water of the entire building they use semiconductor techniques with tunnels around the equipment, making it easier to maintain the environment, and they didn't have to get one single permit for waste treatment because the plant is almost 100% total recycle of air, fumes, and liquid. Copper is plated out of the spent etchant, the ammonia is recaptured and put back in—it was amazing. And we were watching the first runs of 100 panel lots when we were there, and Lionel is doing some evaluation of some new imaging equipment which we can't give you the details on until perhaps spring. 

007: Are they in production now?

Share




Suggested Items

Plating on Silver: What’s Old is New Again

07/07/2022 | Denis Jacques, Technic Inc.
About three decades ago, immersion silver, a nitrate-based process, gained a lot of market share in the world of PCB final finishes. More economical than ENIG, flat, solderable, and conductive, it had everything going for it—everything but corrosion resistance in a harsh environment, that is. Champagne voids were also an issue, along with line reduction. But the worst drawback, the characteristic that made the part short over time, was creep corrosion. A build-up of copper sulfide salt that grows in contact with a sulfur-rich environment, heat, and moisture resulted in failures in the field. This was enough to scar the process for good.

EIPC Summer Conference 2022: Day 2 Review

06/29/2022 | Pete Starkey, I-Connect007
Örebro, Sweden on June 15 brought a bright and early start to Day 2 of the EIPC Summer Conference for those who had enjoyed the previous evening’s networking dinner, but had resisted the temptation to over-indulge or to carry on their long-awaited catch-up conversations with old friends into the small hours. All but a few were in their seats for 9 a.m., awake and attentive for Session 4 of the conference, on the theme of new process technologies, moderated by Martyn Gaudion, CEO of Polar Instruments.

EIPC Summer Conference 2022: Day 1 Review

06/28/2022 | Pete Starkey, I-Connect007
At last, a live EIPC conference and this time in the Swedish city of Örebro, “where history and contemporary culture converge,” a pleasant and convenient location for an event that included a privileged visit to the Ericsson facility in Kumla. Around 100 delegates made the journey and the Örebro Scandic Grand Hotel was an excellent conference venue for the June 14-15 conference.



Copyright © 2022 I-Connect007. All rights reserved.