-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
TTM: Consult Fabricators Early for PCB Designs
July 2, 2015 | Andy Shaughnessy, PCBDesign007Estimated reading time: 6 minutes
Recently, I attended the Designers Council “Lunch and Learn” at Broadcom’s office in Orange County, California. One of the speakers at this event was Julie Ellis, a field applications engineer with TTM Technologies. She sat down with me to discuss her presentation and some of the ways fabricators can assist PCB designers.
Andy Shaughnessy: Julie, why don't you give us a little bit of background about yourself and your history in the industry?
Julie Ellis: I have a degree in electrical engineering and worked as a student and then as an engineer at Hughes Aircraft, which gave me great hands-on experience in RF/analog electronics and coaxial cable design, assembly, and test. After Hughes, I pursued technical sales as a manufacturer’s rep for semiconductors and circuit boards and represented Nan Ya PCB Corp. for ten years before rounding out my career in contract electronics manufacturing as a sales engineer and then global PCB commodity manager. I managed a fabricator’s ISO 9001 quality system and was a technical consultant and process and quality auditor for PCB, CM, and automotive customers before joining TTM.
Shaughnessy: I understand that you train inspectors?
Ellis: Yes. I'm a Certified IPC Trainer for acceptability of both circuit boards (IPC-A-600) and electronic assemblies (IPC-A-610). Untrained inspectors or clients cause tremendous schedule delays when they’re fearful of accepting a product that looks questionable to them, because they worry it could fail in the future. I really enjoy teaching students to understand the requirements and apply the standards to accept product with full confidence.
Shaughnessy: One thing the designers tell us in surveys is that they always want to know more about fab processes. They don’t get to visit board shops very often, if at all. If you can talk to the designers, what would say are a few things that they should do differently?
Ellis: Mainly, I would like to see them engage us, the field applications engineers, before they've started routing out their circuits. Multilayer PCB fabrication requires approximately 30 major process steps, including photoimaging and developing, etching, stripping, lamination, drilling, plating, and screening. Each process has physical or equipment limitations (tolerances) which can negatively impact the product yields or long-term reliability if the design is not optimized. We evaluate the attributes of the design to establish the guidelines for the designer, so their requirements don’t exceed process limitations when they go to fab. We will also create a preliminary stack-up to confirm their requirements for overall and Cu thickness, layer count, controlled impedance, drill and pad sizes can be met.
Secondly, I encourage them to visit one of our sites for a PCB 101 presentation and factory tour. We introduce the processes in a great visual presentation, so they understand what they’re seeing on the production floor.
Shaughnessy: If they get involved with the fabricator earlier, the earlier the better?
Ellis: Definitely! It's a lot easier to modify a design before – rather than after - they've done all the work routing.
Shaughnessy: Today, during your talk, you mentioned a really fascinating new technology that TTM has developed: The Next Generation SMV. Can you tell us a little bit about that?
Ellis: Sure. SMV® is the abbreviation for Stacked MicroVias, a technology which facilitates high density interconnects layer to layer by stacking laser microvias during sequential lamination cycles. SMV starts with a center lamination (sublam) that is drilled, plated, and etched and adds a new set of outer layers with each lamination cycle. A board with 3 layers of SMVs will travel around the production floor through lamination, drill, plate, and etch 3 times, which is very time-consuming.
NextGen-SMV™ also provides Z-axis connectivity from – and to – any layer, but in a single lamination cycle. Specially prepped single-sided cores are laser drilled and filled with copper conductive paste, stacked one on top of another from the bottom up and laminated in our Single Lamination Parallel Process, SLPP™. The pre-filled microvias don’t require plating or additional lamination cycles, so NextGen-SMV technology can be used when extremely fast turn time is required. And because very thin dielectrics are used, NextGen boards are sometimes thinner than standard ones.
Shaughnessy: So these technologies could be used under a micro BGA with lots of I/Os?
Ellis: Exactly. When we look at the grid array under a BGA, we have to consider how we are going to create conductive connections to every circuit board pad corresponding to the grid. The outer pads can be simply routed on the component layer, but when there’s not enough space to run traces between the pads, we have to use an additional layer for each inside row. As each row is connected, it opens routing for the next row.
Shaughnessy: It looks like it would be really hard to fabricate. I mean, if each row of the array pattern requires its own routing layer, it must be tough to build.
Ellis: It significantly increases complexity and requires enabling equipment and processing. Laser drills have to be used for microvias. And registration has to be dead-on, or the lasers can partially miss their landing pads and drill through the layers below. So we use Laser Direct Imaging, or LDI. And to plate these small holes, we developed reverse pulse plating processes with our plating chemistry supplier to assure continuous plating into single-ended (microvias that are drilled down and stop at the next layer) and high aspect ratio (drill depth:drill diameter) through-holes. It’s interesting to note that standard through-hole capability aspect ratio is 10:1, but because single-ended holes are so much more difficult to plate, microvia standard aspect ratio is preferred 0.5:1.Page 1 of 2
Suggested Items
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources:
Matrix to Exhibit at IPC APEX EXPO 2024 in Anaheim, CA
03/05/2024 | MatrixMatrix will be exhibiting at IPC APEX EXPO 2024, to be held on April 9-12, 2024, at the Anaheim Convention Center, Anaheim, CA.
The Chemical Connection: Getting to Know Your Vendor
02/16/2024 | Don Ball -- Column: The Chemical ConnectionAfter working for a capital equipment supplier for almost 50 years, I’ve found that the most important part of getting to know your vendor is good communication among all parties. While contact between fabricators of a constantly changing product line and the designers of those products may occur daily or weekly, conversations between you and your equipment supplier may be years apart. That lengthy gap often means that previous contacts may have been promoted, retired, or moved on to other opportunities. You may have also migrated to a new supplier with whom you have little or no history. In either case, you will be interacting with someone you are unfamiliar with (as they are with you). Therefore, it is essential for both sides to communicate clearly so expectations will align.
EIPC Winter Conference 2024, Day 2: A Closer Look at Global Trends
02/14/2024 | Pete Starkey, I-Connect007The opening session of the second day’s conference proceedings focused on global PCB trends and was introduced and moderated by Dr. Michele Stampanoni, vice president of strategic sales and business development at Cicor Group in Switzerland. He opened the session with Dr. Hayao Nakahara’s knowledgeable and enlightening video presentation on the IC substrates industry.